View PS9817-2-V-F3_1181095.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ps9817-1,-2 nec's high cmr, 10mbps open collector output type 8-pin ssop (so-8) high-speed optocoupler california eastern laboratories ? pulse width dist ort ion : |t phl - t plh | = 35 ns max. ? high common mode transient immunity: cm h , cm l = 15 kv/ s min. ? 40% reduction of mounting area: 5-pin sop x 2 ? high speed: 10 mbps ? high isolation voltage: bv = 2 500 v r.m.s. ? open collector output ? ordering number of taping product: ps9817-1-f3, f4: 1 500 pcs/reel ps9817-2-f3, f4: 1 500 pcs/reel ? pb-free product ? safety standards: ul approved: file no. e72422 din en60747-5-2 (vde0884 part2) approved no. 40008347 (option) features data sheet nec's ps9817-1 and ps9817-2 are active-low type high-speed photocouplers that use a gaalas light-emitting diode on the input side and a photodetector ic that includes a photodiode and a signal processor on the same chip on the output side. nec's ps9817-1 and ps9817-2 are designed speci?cally for high common mode transient immunity (cmr) and low pulse width distortion, the ps9817-2 is suitable for high density applications. description ? measurement equipment ? pdp ? fa network application truth table led output on l off h 1 2 3 4 8 7 6 5 ps9817-1 1. nc 2. anode 3. cathode 4. nc 5. gnd 6. v o 7. nc 8. v cc 1 2 3 4 8 7 6 5 shield shield ps9817-2 1. anode1 2. cathode1 3. cathode2 4. anode2 5. gnd 6. v o 2 7. v o 1 8. v cc pin connection (t op v iew)
ps9817-1,-2 package dimensions (unit: mm) marking example 1.27 0.4 +0.10 -0.0 5 0.25 m 0.10.1 3.950.1 6.00.2 0.50.3 0.15 +0.10 -0.0 5 5.210.25 3.270.2 0.10 s 1 4 8 5 no. 1 pin mark initial of nec (engraved mark) ps9817-1 ps9817-2 no. 1 pin mark initial of nec (engraved mark) assembly lot n 9817-2 nl251 w eek assembled assembly lot n 9817-1 nl251 2 51 ye ar assembled (last 1 digit) l n rank code in-house code (l: pb-free) 2 51 year assembled (last 1 digit) l n rank code in-house code (l: pb-free) w eek assembled
ps9817-1,-2 ordering information *1 for the application of the safety standard, following part number should be used. *2 with regards to terminal solder (the solder contains lead) plated products (conventionally plated), contact your nearby sales of?ce. part number order number solder plating specification packing style safety standards approval application part number *1 ps9817-1 ps9817-1-a pb-free *2 20 pcs (tape 20 pcs cut) standard products ps9817-1 ps9817-1-f3 ps9817-1-f3-a embossed tape 1500 pcs/reel (ul approved) ps9817-1-f4 ps9817-1-f4-a ps9817-2 ps9817-2-a 20 pcs (tape 20 pcs cut) ps9817-2 ps9817-2-f3 ps9817-2-f3-a embossed tape 1500 pcs/reel ps9817-2-f4 ps9817-2-f4-a ps9817-1-v ps9817-1-v-a 20 pcs (tape 20 pcs cut) din en60747-5-2 ps9817-1 ps9817-1-v-f3 ps9817-1-v-f3-a embossed tape 1500 pcs/reel (vde0884 part2) ps9817-1-v-f4 ps9817-1-v-f4-a approved ps9817-2-v ps9817-2-v-a 20 pcs (tape 20 pcs cut) (option) ps9817-2 PS9817-2-V-F3 PS9817-2-V-F3-a embossed tape 1500 pcs/reel ps9817-2-v-f4 ps9817-2-v-f4-a
ps9817-1,-2 recommended operating conditions absolute maximum ratings ( t a = 25oc, unless otherwise speci?ed ) *1 reduced to 0.3 ma/ c at t a = 60 c or more. *2 reduced to 0.1 ma/ c at t a = 60 c or more. *3 applies to output pin v o (collector pin). reduced to 1.5 mw/ c at t a = 65 c or more. *4 ac voltage for 1 minute at t a = 25 c, rh = 60% between input and output. parameter symbol ratings unit ps9817-1 ps9817-2 diode forward current i f 20 *1 15 *2 ma reverse voltage v r 5 v/ch detector supply voltage v cc 7 v output voltage v o 7 v/ch output current i o 25 ma/ch power dissipation *3 p c 40 mw/ch isolation voltage *4 bv 2 500 vr.m.s. operating ambient temperature t a ? 40 to +85 c storage temperature t stg ? 55 to +125 c parameter symbol min. typ. max. unit low level input voltage v fl 0 0.8 v high level input current i fh 6.3 10 12.5 ma supply voltage v cc 4.5 5.5 v pull-up resistance r l 330 4 k tll (r l = 1.0 k , loads) n 5
ps9817-1,-2 electrical characteristics ( t a = -40 to 85 oc, un less otherwise speci?ed ) parameter symbol conditions min. typ. *1 max. unit diode forward voltage v f i f = 10 ma, t a = 25 c 1.4 1.65 1.8 v reverse current i r v r = 3.0 v, t a = 25 c 10 a terminal capacitance c t v f = 0 v, f = 1 mhz, t a = 25 c 30 pf detector high level output current i oh v cc = v o = 5.5 v, v f = 0.8 v 1 100 a low level output voltage *2 v ol v cc = 5.5 v, i f = 5.0 ma, i ol = 13 ma 0.2 0.6 v high level supply current (ps9817-1) i cch v cc = 5.5 v, i f = 0 ma, v o = open 5 8 ma high level supply current (ps9817-2) 9 16 low level supply current (ps9817-1) i ccl v cc = 5.5 v, i f = 10 ma, v o = open 10 11 low level supply current (ps9817-2) 18 22 coupled threshold input current (h l) i fhl v cc = 5.0 v, v o = 0.8 v, r l = 350 2.0 5 ma isolation resistance r i-o v i-o = 1 kv dc , rh = 40 to 60%, t a = 25 c 10 11 insulation resistance (input-input), (ps9817-2) r i-i v i-i = 1 kv dc , rh = 40 to 60%, t a = 25 c 10 10 isolation capacitance c i-o v = 0 v, f = 1 mhz, t a = 25 c 0.6 pf insulation capacitance (input-input), (ps9817-2) c i-i v = 0 v, f = 1 mhz, t a = 25 c 0.3 pf propagation delay time (h l) *3 t phl t a = 25 c 40 75 ns v cc = 5.0 v, r l = 350 , i f = 7.5 ma 100 propagation delay time (l h) *3 t plh t a = 25 c 45 75 v cc = 5.0 v, r l = 350 , i f = 7.5 ma 100 rise time t r v cc = 5.0 v, r l = 350 , i f = 7.5 ma 20 fall time t f 5 pulse width distortion (pwd) *3 |t phl ? t plh | 5 35 propagation delay skew t psk 40 common mode transient immunity at high level output *4 cm h v cc = 5.0 v, r l = 350 , t a = 25 c, i f = 0 ma, v o > 2 v, v cm = 1 kv 15 20 kv/ s common mode transient immunity at low level output *4 cm l v cc = 5.0 v, r l = 350 , t a = 25 c, i f = 7.5 ma, v o < 0.8 v, v cm = 1 kv 15 20 *1 typical values at t a = 25 c *2 because v ol of 2 v or more may be output when led current input and when output supply of v cc = 2.6 v or less, it is important to con?rm the characteristics (operation with the power supply on and of f) during design, before using this device.
ps9817-1,-2 *3 test circuit for propagation delay time remark c l includes probe and stray wiring capacitance. *4 test circuit for common mode transient immunity usage cautions 1. this product is weak for static electricity by designed with high-speed integrated circuit so protect against static electricity when handling. 2. by-pass capacitor of 0.1 f is used between v cc and gnd near device. also, ensure that the distance between the leads of the photocoupler and capacitor is no more than 10 mm. 3. avoid storage at a high temperature and high humidity. ps9817-1 shield shield ps9817-2 input output 50% 1.5 v v ol t phl t plh (i f = 7.5 ma) v cc = 5 v 0.1 f c l = 15 pf 47 ? r l = 350 ? v cc = 5 v 0.1 f c l = 15 pf 47 ? r l = 350 ? pulse input (i f ) (pw = 1 s, duty cycle = 1/10) input (monitor ) v o (monitor ) v o (monitor ) pulse input (i f ) (pw = 1 s, duty cycle = 1/10) input (monitor ) 90% 10% 1 kv 0 v v oh 2 v 0.8 v v ol v cm v o (i f = 0 ma) v o (i f = 7.5 ma) t r t f sw i f v o (monitor) v cc = 5 v 0.1 f r l = 350 ? ps9817-1 v cm c l = 15 pf shield shield v o (monitor) v cc = 5 v 0.1 f r l = 350 ? v cm sw i f c l = 15 pf ps9817-1
ps9817-1,-2 remark the graphs indicate nominal characteristics. typical characteristics ( t a = 25oc, unless otherwise speci?ed ) detect or power dissip at ion vs. ambient tempera ture ambient t emperature t a (oc) detector power dissipation p c (mw) 20 40 60 80 85 100 0 20 10 30 50 40 forward v oltage v f (v) forward current i f (ma) for w ard current vs. for w ard vol t age 1.0 0.01 0.1 1 10 100 1.2 1.4 1.6 1.8 2.0 2.2 2.4 t a = +85oc +50oc +25oc 0oc -25oc -50 -25 0 25 50 7 5 100 i f = 5.0 ma, v cc = 5.5 v 0.6 0.5 0.4 0.3 0.2 0.1 0 13.0 ma 10.0 ma 6.0 ma i ol = 16.0 ma -50 -25 0 25 5 0 7 5 100 0 20 18 16 14 12 10 8 6 4 2 i ccl (i f = 10 ma), ps9817-2 i cch (i f = 0 ma), ps9817-1 i ccl (i f = 10 ma), ps9817-1 i cch (i f = 0 ma), ps9817-2 1 2 3 4 5 6 6 5 4 3 2 1 0 r l = 350 ? v cc = 5.0 v, t a = 25oc 1.0 k ? 4.0 k ? , 4.7 k ? ambient t emperature t a (oc) maximum forward current i f (ma) maximum for w ard current vs. ambient tempera ture 20 40 60 80 100 0 85 10 20 30 25 15 5 ps9817-1 ps9817-2 ambient t emperature t a (oc) high level supply current i cch (ma) low level supply current i ccl (ma) suppl y current vs. ambient tempera ture input current i f (ma) output v oltage v o (v) output vol t age vs. input current ambient t emperature t a (oc) low level output v oltage v ol (v) low level output vol t age vs. ambient tempera ture
ps9817-1,-2 v cc = 5.0 v, v o = 0.6 v 5 4 3 2 1 0 60 50 40 30 20 10 0 100 80 60 40 20 0 -50 -25 0 25 50 7 5 100 -50 -25 0 25 50 7 5 100 -50 -25 0 25 50 7 5 100 1.0 k ? r l = 350 ? i f = 7.5 ma, v cc = 5.0 v i f = 7.5 ma, v cc = 5.0 v t phl : r l = 350 ?, 1.0 k ?, 4.0 k ?, 4.7 k ? r l = 4.7 k ? r l = 350 ? 1.0 k ? 15 13 11 9 7 5 -50 -25 0 25 50 7 5 100 i f = 7.5 ma, v cc = 5.0 v v cc = 5.0 v, t a = 25o c 300 250 200 150 100 50 0 120 100 80 60 40 20 0 t r : r l = 4.7 k ? t plh : r l = 4.0 k ? t r : r l = 1.0 k ? t r : r l = 350 ? t f : r l = 350 ? , 1.0 k ? , 4.0 k ? , 4.7 k ? 4.0 k ? t plh : r l = 1.0 k ? t plh : r l = 350 ? t plh : r l = 4.7 k ? t plh : r l = 4.0 k ? 4.0 k ? t r : r l = 4.0 k ? t plh : r l = 350 ? , 1.0 k ? t phl : r l = 350 ? , 1.0 k ? , 4.0 k ? threshold input current vs. ambient tempera ture ambient t emperature t a (oc) threshold input current i fhl (ma) ambient t emperature t a (oc) propagation delay t ime t phl , t plh (ns) prop agat ion dela y time vs. ambient tempera ture ambient t emperature t a (oc) pulse width distortion t phl ?t plh (ns) pulse width dist or tion vs. ambient tempera ture ambient t emperature t a (oc) switching t ime t r , t f (ns) switching time vs. ambient tempera ture input current i f (ma) propagation delay t ime t phl , t plh (ns) prop agat ion dela y time vs. input current
ps9817-1,-2 taping specifications (unit:mm) 4.05 max. outline and dimensions (reel) packing: 1 500 pcs/reel 2.00.5 r 1.0 13.00.2 21.00. 8 3302.0 1001.0 2.0 0.5 11 .9 to 15.4 outer edge of flange 17.51.0 13.51.0 13.00.2 1.70.1 2.00.05 4.00.1 1.750.1 6.40.1 5.560.1 0.30.05 8.00.1 1.5 +0.1 -0 5.50.1 12.00.2 3.60.1 outline and dimensions (t ape) t aping direction ps9817-1-f3 ps9817-2-f3 ps9817-1-f 4 ps9817-2-f 4
ps9817-1,-2 recommended mount pad dimensions (unit:mm) 1.45 0.8 1.27 5.25
ps9817-1,-2 notes on handling 1. recommended soldering conditions (1) infrared re?ow soldering ? peak re?ow temperature 260 c or below (package surface temperature) ? time of peak re?ow temperature 10 seconds or less ? time of temperature higher than 220 c 60 seconds or less ? time to preheat temperature from 120 to 180 c 120 30 s ? number of re?ows three ? flux rosin ?ux containing small amount of chlorine (the ?ux with a maximum chlorine content of 0.2 wt% is recommended.) (2) wave soldering ? temperature 260 c or below (molten solder temperature) ? time 10 seconds or less ? preheating conditions 120 c or below (package surface temperature) ? number of times one (allowed to be dipped in solder including plastic mold portion.) ? flux rosin ?ux containing small amount of chlorine (the ?ux with a maximum chlorine content of 0.2 wt% is recommended.) (3) soldering by soldering iron ? peak temperature (lead part temperature) 350 c or below ? time (each pins) 3 seconds or less ? flux rosin ?ux containing small amount of chlorine (the ?ux with a maximum chlorine content of 0.2 wt% is recommended.) (a) soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead (b) please be sure that the temperature of the package would not be heated over 100 c 12030 s (preheating) 220oc 180oc package surface t emperature t (oc) t ime (s) recommended temperature profile of infrared reflow (heating) to 10 s to 60 s 260oc max. 120oc
ps9817-1,-2 (4) cautions ? fluxes avoid removing the residual ?ux with freon-based and chlorine-based cleaning solvent. 2. cautions regarding noise be aware that when voltage is applied suddenly between the photocouplers input and output or between collector-emitters at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings. usage cautions 1. protect against static electricity when handling. 2. avoid storage at a high temperature and high humidity. life support applications these nec products are not intended for use in life support devices, appliances, or systems where the malfunction of these prod ucts can reasonably be expected to result in personal injury . the customers of cel using or selling these products for use in such applications do so at their own risk and agree to fully indemnify cel for all damages resulting from such improper use or sale. a business partner of nec compound semiconductor devices, ltd. 04/04/2005

▲Up To Search▲

Price & Availability of PS9817-2-V-F3

	To Download PS9817-2-V-F3 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .